1．檢查空壓機各零件局部能否完好，各維護安裝、儀表、閥門、管路及接頭能否有損壞或松動。 2．略為翻開油氣桶底部的排水閥，排出光滑油下部積存的冷凝水和污物，見到有油流出即打開，以防光滑油過早乳化蛻變。 3．檢查油氣桶油位能否在油位計二條刻度線之間，缺乏時應補充。留意加油前確認系統內無壓力（油位以停機非常鐘后察看為準，在運轉中油位較停機時稍低）。 4．新機第一次開機或停用較長時間又開機，應先拆下空氣過濾器蓋，從進氣口參加約0.5升左右光滑油，以防起動機遇內失油燒損。 5．確認系統內無壓力。 6．翻開排氣閥門。 7. 檢測銜接至空壓機的電纜，電壓能否契合廠家請求（電壓360V-410V之間），請求設備未開機和開機工作后都要檢測，有些工廠靜態電壓無異常，負載后電壓降落，會招致電機過載。
1. Check whether the parts of the air compressor are in good condition, whether the maintenance and installation, meters, valves, pipelines and joints are damaged or loosened. 2. Open the drain valve at the bottom of the oil and gas barrel slightly, drain the condensate and dirt accumulated at the bottom of the smooth oil, and open it when oil flows out, so as to prevent premature emulsification and degeneration of the smooth oil. 3. Check whether the oil level of oil and gas barrel can be between the two calibration lines of oil level gauge, when it is lacking, it should be supplemented. Make sure that there is no pressure in the system before refueling (oil level should be checked ten minutes after shutdown, which is slightly lower in operation than when shutdown). 4. When the new engine starts or stops working for a long time and starts again, the cover of the air filter should be removed first, and about 0.5 litres of smooth oil should be added from the intake port to prevent loss of oil and burning in the starting opportunity. 5. Make sure there is no pressure in the system. 6. Open the exhaust valve. 7. Test whether the voltage of the cable connected to the air compressor meets the manufacturer's request (voltage between 360V and 410V). If the request equipment is not turned on and turned on, it must be tested. Some factories have no abnormal static voltage. The voltage drop after load will cause overload of the motor.
II. Starting steps
1．合上開關手把。 2．點動，檢查電動機轉向能否正確，有加裝換相維護安裝的除外。 3．確認手動閥處于“卸載”狀態，按下“起動”按鈕即正式運轉，于數秒后，將手動閥撥至“加載”位置，壓力逐步上升至額定壓力，而光滑油低于排氣壓力0.25Mpa左右。 4．察看運轉能否平穩，聲音能否正常，空氣對流能否暢通，儀表讀數能否正常，能否走漏。
1. Close the switch handle. 2. Point, check whether the motor steering is correct, except for installation, commutation maintenance and installation. 3. To confirm that the manual valve is in the "unloading" state, press the "start" button to operate formally. After a few seconds, the manual valve is set to the "loading" position, and the pressure gradually rises to the rated pressure, while the smooth oil is lower than the exhaust pressure of about 0.25 Mpa. 4. Check whether the operation is stable, whether the sound is normal, whether the air convection is smooth, whether the instrument reading is normal, whether leaks.
III. Notices in Operation
1．經常察看各儀表能否正常。 2．經常傾聽空壓機各部位運轉聲音能否正常。 3．經常檢查有無滲漏現象。 4．在運轉中如發現油位計上看不到油位，應立刻停機，10分鐘后再察看油位，如缺乏，待系統內無壓力時再補充。 5．經常堅持空壓機表面及四周場所潔凈，嚴禁在空壓機上放置任何物件，如工具、抹布、衣物、手套等。 6．遇有特殊狀況，按“急停處置”。
1. Check every instrument regularly. 2. Listen regularly to the sound of air compressor operation. 3. Check for leakage regularly. 4. If the oil level can not be seen on the oil level gauge in operation, stop immediately and check the oil level 10 minutes later. If there is a lack of oil level, replenish it when there is no pressure in the system. 5. Often adhere to the air compressor surface and surrounding areas clean, strictly prohibit the placement of any objects in the air compressor, such as tools, rags, clothing, gloves, etc. 6. In case of special circumstances, the case shall be handled as "urgent".
Put the manual valve to the "unloading" position to unload the air compressor. After ten seconds or so, press the "stop" button. The motor stops running and the switch handle is set to zero.
1．當呈現下列狀況之一時，應緊急停機： （1）呈現異常聲響或振動時； （2）排氣壓力超越平安閥設定壓力而平安閥未翻開； （3）排氣溫度超越100度時未自動停機； （4）四周發作緊急狀況時； 2．緊急停機時，無需先卸載，可直接按下“中止”鈕。
1. When one of the following situations occurs, emergency shutdown should be made: (1) when abnormal sound or vibration occurs; (2) when exhaust pressure exceeds the set pressure of safety valve and safety valve does not open; (3) when exhaust temperature exceeds 100 degrees, it does not automatically shut down; (4) when emergency occurs around; and (2) when emergency shutdown occurs, it is not necessary to unload first, it can directly press the "stop" button.