1. <th id="wxip0"><pre id="wxip0"></pre></th>
    <em id="wxip0"><strike id="wxip0"><u id="wxip0"></u></strike></em>

    <rp id="wxip0"></rp>
    <rp id="wxip0"></rp>
    <tbody id="wxip0"></tbody>
    <rp id="wxip0"></rp>
    1. <progress id="wxip0"><big id="wxip0"></big></progress>
    2. 濟南科邦機械設備有限公司您身邊的濟南空壓機廠家!
      18765879198

      首頁>企業新聞
      空氣壓縮機的安裝對于環境有什么要求?
      Time:2019-04-17 14:29:37       來源:http://www.592free.com/      

      一、空氣緊縮機裝置環境請求

      I. Environmental Requirements for Air Compressor Devices
      1、空壓機應裝置在四周環境清涼、空氣濕度低、灰塵少的中央。若必需裝置在酷熱或多塵的環境中,則要經過導管盡可能從清涼、少塵的中央汲取空氣并盡可能降低空氣的濕度。
      1. The air compressor should be installed in the center with cool surroundings, low air humidity and little dust. If it is necessary to install it in a hot or dusty environment, it is necessary to draw air from a cool, dusty center as much as possible through a catheter and to reduce the humidity of the air as much as possible.
      2、環境溫度應低于40℃,如高于40℃應采取措施增強通風,以防止高溫停車。
      2. The ambient temperature should be lower than 40 C. If it is higher than 40 C, measures should be taken to enhance ventilation in order to prevent high temperature parking.
      3、四周應留有一定空間,以便檢修和拆裝部件。
      3. There should be some space around for repairing and disassembling parts.
      空氣緊縮機
      Air Compressor
      二、空氣緊縮機裝置根底請求
      II. Fundamental Requirements for Air Compressor Devices
      1、因螺桿式空壓機自身振動很小,空壓機只需裝置在質地較硬外表平整的程度空中上。若加墊8~15mm厚的橡膠減振墊或木板對防振降噪更有利。
      1. Because the screw air compressor itself has little vibration, the air compressor only needs to be installed in the air with a more rigid surface. It is more advantageous to prevent vibration and noise if rubber cushion or wood board with thickness of 8-15mm is added.
      濟南空壓機
      2、以機器上與地平面平行的加工面或底座平面作為基準,用程度儀丈量程度,縱橫程度控制在0.2mm/m范圍內較好。
      2. It is better to control the vertical and horizontal degree in the range of 0.2m m/m by using the degree meter to measure the degree on the processing surface or the base plane parallel to the ground plane on the machine.
      三、空氣緊縮機管路裝置請求
      3. Request for Pipeline Device of Air Compressor
      1、與機器銜接的管道,裝置前必需將內部處置潔凈,不應有浮銹、熔渣、焊珠及其他雜物。
      1. Pipelines connected with machines must be cleaned before installation. There should be no floating rust, molten slag, welding beads and other impurities.
      2、氣體管道和管件的最大允許工作壓力應超越額定排氣壓力的1.5倍或0.1Mpa,兩者取大值,且大于平安閥的調定壓力。
      2. The maximum allowable working pressure of gas pipeline and fittings should exceed 1.5 times or 0.1 Mpa of rated exhaust pressure, both of which are larger than the setting pressure of safety valve.
      3、主管路應有一定的傾斜度,以利管路中凝結水集中排出。
      3. The main pipeline should have a certain inclination to facilitate the centralized discharge of condensate water in the pipeline.
      4、管路壓力降不得超越空壓機設定壓力的5%。配管管徑不要恣意減少,如必需減少或放大管徑必需運用漸縮管,否則,在接頭處回構成紊流招致較大壓力損失。
      4. Pipeline pressure drop shall not exceed 5% of the set pressure of the air compressor. Pipe diameters should not be arbitrarily reduced. If it is necessary to reduce or enlarge pipe diameters, it is necessary to use tapered pipes. Otherwise, turbulence at the joint will cause greater pressure loss.
      5、若系統用氣量動搖較大倡議裝備加裝緩沖,這樣可減少空壓機負載運轉次數。理想的配置型式為:空壓機→ 氣水別離器→ 儲氣罐→ 精細過濾器→ 枯燥機→ 精細過濾器
      5. If the system is shaken by air, it is advisable to install buffer equipment, which can reduce the number of air compressor load operation. The ideal configuration type is: air compressor gas-water separator gas storage tank fine filter dryer fine filter.
      6、管路中盡可能減少彎頭和各類閥門,以減少壓力損失。
      6. Reduce elbows and valves as much as possible in the pipeline to reduce pressure loss.
      7、用氣設備多且較分散時,主管路應環繞整個廠房,這樣,任何位置均可取得兩個方向的緊縮空氣,減少壓力降。支線管路必需從主管路上方引出,以防止管路中的凝結水流至用氣輸出端口。
      7. When there are many and dispersed gas-using equipment, the main road should surround the whole factory building, so that the compressed air in two directions can be obtained at any position to reduce the pressure drop. Branch pipelines must be drawn from above the main road to prevent condensate flow in the pipeline from reaching the gas output port.

      電話:0531-85963300     手機:18765879198   地址:濟南市天橋區無影山中路130號重汽彩世界     備案號:魯公網安備 37010502001004號 >

      版權所有:濟南科邦機械設備有限公司 濟南科邦機械主營::濟南空壓機及配件 網址:http://www.592free.com    技術支持:諾商信息  

      魯公網安備 37010502001004號

      1. <th id="wxip0"><pre id="wxip0"></pre></th>
        <em id="wxip0"><strike id="wxip0"><u id="wxip0"></u></strike></em>

        <rp id="wxip0"></rp>
        <rp id="wxip0"></rp>
        <tbody id="wxip0"></tbody>
        <rp id="wxip0"></rp>
        1. <progress id="wxip0"><big id="wxip0"></big></progress>
        2. 久久婷婷五月综合色丁香_亲胸揉屁股膜下刺激视频午夜_丰满少妇被猛烈进入高清播放_三上悠亚ssni绝顶を教え込ま